What’s the Difference Between Polyurethane, Varnish, Shellac and Lacquer?

The ravages of time and use can be limited by a durable top or finish coat on your furniture. While the terms varnish, polyurethane, lacquer and shellac are commonly used to reference a final finish in general, these products are not the same, nor is it recommended that they be used interchangeably.

Shellac

This finish is actually a natural product (it’s made from combining a secretion from the female lac bug with a solvent such as alcohol) that is very safe once dried and hardened. In addition to adding a protective coat, it also can add a warm amber color to wood. It can be affected by heat (white rings will appear under a hot bowl or mug) or chemicals, so a kitchen table might not be the best place to use it. Fine furniture items can be greatly enhanced with shellac. Some shellac manufacturers recommend using it as a protective coat on non-wood items. Apply it with a natural bristle brush or with a cotton rag.

Shellac is available in most home centers as a liquid in a can. It also comes in solid form or in flakes that must be dissolved, and it has a shorter shelf life than other finishes. The liquid variety is the best option for the average homeowner.

Polyurethane

Essentially a plastic in the form of a liquid until it dries, polyurethane is available in both water- and oil-based options, and comes in a variety of finishes from satin to glossy. Water-based polyurethane is popular because of its low odor and low toxicity. It goes on clear without adding a slight color that oil-based versions can, and it dries much faster. As with shellac, water-based polyurethane won’t hold up well to heat and chemicals. It’s good for bookcases, desks, side tables and picture frames — anything that won’t be exposed to extremes.

Minwax Polycrylic is an example of a fortified water-based polyurethane that can stand up a bit better to rough conditions. It also can go over oil-based finishes and can be applied using synthetic-bristle brushes, a foam roller or a rag, as can other water-based polyurethanes. Water-based oil-modified polyurethane is a relatively new product that combines the durability of an oil base with the cleanup of a water base. This product can actually be used on wooden floors.

Oil-based polyurethane is slightly more durable than water-based, especially when it comes to handling heat, so a kitchen table is a good candidate for this finish. It adds a slight color tone and will bring out the richness of wood. When working with oil-based polyurethane, use a respirator in a well-ventilated area. Apply using a natural-bristle brush or rag. Oil-based takes much longer to dry and cure than water-based, so plan accordingly and follow the manufacturer’s directions.

Both oil- and water-based polyurethane can be applied to latex/acrylic paint, however oil-based polyurethane will create a yellow or amber hue, especially to light colors. To add durability without affected color, use a water-based finish.

You can also purchase polyurethane in a spray can which makes it a bit easier to apply, especially on large projects. Wipe-on polyurethane is used primarily by woodworkers who want to create a “hand-rubbed” finish on special projects. These two are on the opposite ends of spectrum as far as ease of use, but produce excellent results.

Varnish

The name of this finish often is used generically for a finish or top coat. It’s very durable because it contains a higher ratio of solids. Spar varnish is perfect for outdoor projects and for raw wood used for exterior doors and trim on rustic homes. In addition to protecting the wood, it also provides natural ultraviolet light protection. Spar varnish is often used on items that will be near or on the water, like a wood boat, decks, beach chairs, etc. Apply using a natural-bristle brush.

Lacquer

Lacquer provides the extremely intense gloss finish often used on many Asian-inspired or ultramodern furnishings. It is extremely durable and resistant to damage, however over time it can begin to discolor and become scratched. Wonder why it’s so smooth? It’s applied via a sprayer, because it is thinner than the other finishes. You’ll need a high-volume, low-presser (HVLP) sprayer and a well-ventilated and spacious workspace to apply it.

Other Finishes

Cutting boards and other wood items that come in contact with food do well with butcher-block oil and food-grade mineral oil. Wooden tool handles will hold up better with an annual rubdown using boiled linseed oil.

What are the best ways to Apply these Finishes?

The general rule of thumb is to use natural brushes, sometimes referred to as China bristle brushes, for all oil-based finishes (including paint), and synthetic brushes, sometimes referred to as nylon brushes, for latex, acrylic or water-based finishes. Rollers and rags can work for either type of finish.

Because these are the top coats being applied, you’ll want them to look as good and as smooth as possible. The best conditions for application are when there is as little dust or other airborne particles as possible. Clean your work area as thoroughly as possible and allow some time for the dust (literally) to settle. Consider using a dust collection system or air purifier.

When applying a finish with a brush or roller, you may notice some bubbles pop up. Don’t panic. Many times these will settle out as the finish dries. If bubbles are a problem, simply wipe down with a rag. You can often avoid this by applying a thinner coat. Also, shaking a can of finish will certainly add bubbles, so try stirring instead.

After the first coat dries, you’ll need to either sand it with fine-grit sandpaper (220 grit) or use steel wool. You may have heard to only use steel wool, but many manufacturers recommend either one. Just be careful not to deeply scratch the finish and certainly do not sand off the finish to the point where you reach raw wood. Wipe off the dust created and apply another coat. A couple of coats are usually enough, but you can apply additional coats (more wiped-on coats can be applied than brushed or rolled) to create a thicker and more durable finish. Try not to exceed four or five coats of finish.

—
Photo Credit:  photographerstudio / Shutterstock.com